Product Description

 

Product Description

Automatic folding and sealing machine, automatically fold the lid, automatically paste the tape up and down, without manual work; using instant tape carton sealing, the sealing effect is smooth and beautiful, and the sealing is firm. It can be operated by a single machine or can be equipped with an automated packaging line. It is widely used in food, medicine, beverage, tobacco, daily chemical, automobile, cable, electronics and other industries.

Features:

* Autonomous adjustment of height and width. Manually adjust the width and height of the machine according to the carton specifications, which is suitable for carton sealing of the same specifications at the same time;
* The sealing is beautiful Pneumatic sealing, fast and beautiful;
* Save labor The packaging of goods is done by machines instead of labor;
* Improve efficiency Stable sealing speed, higher efficiency;
* Simple operation The simple operation panel is economical, durable, safe, and has low failure rate.

Product Parameters

Model	GPC-50D
Conveyor Speed	18m/min
Compatible Carton Size	Length 200-600mm  Width 150-500mm  Height 150-500mm
Working Voltage	110/220V 50/60Hz 1Phase
Power	400w
Tape Size	48/60/75mm (Use 1 of them)
Air Consumption	50NL/min
Necessary Air Pressure	0.6Mpa
Table Height	600+150mm
Machine Size	1770*850*1520mm
Machine Weight	250kg

Fast installation tape design
Only need to grasp the tape arm, you can easily remove the movement, convenient and quick to install the tape, simple operation.

Selected configuration, stable and durable
Selected powerful motors to ensure stable and smooth operation of the whole machine.

Stainless steel drum
Durable, no rust, good bearing capacity.

Width and height can be adjusted independently
The width and height can be manually adjusted according to the carton specifications, and the operation is simple and convenient.

Cylinder control
Airtac cylinders are used to control the movement and the folding mechanism to reduce the resistance of the folding and sealing, and the packaging is convenient and smooth. It not only avoids the waste of adhesive tape, but also makes the sealing position more precise.

Switch
Select high-performance power switch, and the service life of the key switch can reach 100,000 times.

Scale ruler
Equipped with a height scale, convenient for users to adjust.

Sealing effect
Adhesive carton with adhesive tape, no skewing, no bubbles, beautiful and neat.

 

Certifications

 

 

Company Profile

ZheJiang CZPT Intelligent Equipment Co., Ltd. was established in 2009, focusing on the R & D, manufacturing and sales of Multi-hea Weighers, VFFS, Conveyors and Inspection equipment, the products are exported to more than 80 countries and regions.
Company’s 10,12,14,20,24,32 head microcomputer control and PLC control system intelligent combination scale, automatic weight detection machine and 1,2,4,8 head linear scale,creates and applies the combination scale developed by Siemens PLC and Allen Bradley PLC in China, which fills the technical gap of the same industry in China.
ZheJiang CZPT Intelligent Equipment Co., Ltd. adheres to customer-oriented, provides innovative, attractive and easy-to-use products for customers, and is committed to improving people’s working conditions.Pre-sales guidance service: provide professional solutions from workers, equipment, packaging materials, packaging methods and working environment.

Packaging & Shipping

FAQ

1. Where is your factory located?
Our factory is located in HangZhou City,ZheJiang Province which near ZheJiang ,about 2 hours by train.
our machines are designed easy for installation; Installation video is also available. If needed, we’ll arrange professional engineer to service overseas if buyers bear related cost.

2. How to install the machine?
Our machines are designed easy for installation; Installation video is also available. If needed, we’ll arrange professional engineer to service overseas if buyers bear related cost.

3. Do you have aftersales service for this machine?
We have experienced after-sales team ready to solve the problems for our buyers. Buyers describe the problems to us by email or telephone; sometimes we need you to supply the problem pictures and videos for our engineers for reference, we will try to discuss with buyers and try to get the most effective solution in shortest time. If necessary, we can arrange the most professional engineer to go to buyer’s factory for solving problems as soon as possible.

4. How about your warranty?
We offer 1 year warranty and life-long maintenance. In the first year, if any parts broken not occurred by human factor and parts not in the list of 1% free spare parts, we will supply the new replacement parts freely.

5. Do you have OEM service?
Yes. OEM service is available. Our designer would make your private idea into being. We will protect your sales area, ideas of design and all private information belonged to you.

Guide to Drive Shafts and U-Joints

If you’re concerned about the performance of your car’s driveshaft, you’re not alone. Many car owners are unaware of the warning signs of a failed driveshaft, but knowing what to look for can help you avoid costly repairs. Here is a brief guide on drive shafts, U-joints and maintenance intervals. Listed below are key points to consider before replacing a vehicle driveshaft.

Symptoms of Driveshaft Failure

Identifying a faulty driveshaft is easy if you’ve ever heard a strange noise from under your car. These sounds are caused by worn U-joints and bearings supporting the drive shaft. When they fail, the drive shafts stop rotating properly, creating a clanking or squeaking sound. When this happens, you may hear noise from the side of the steering wheel or floor.
In addition to noise, a faulty driveshaft can cause your car to swerve in tight corners. It can also lead to suspended bindings that limit overall control. Therefore, you should have these symptoms checked by a mechanic as soon as you notice them. If you notice any of the symptoms above, your next step should be to tow your vehicle to a mechanic. To avoid extra trouble, make sure you’ve taken precautions by checking your car’s oil level.
In addition to these symptoms, you should also look for any noise from the drive shaft. The first thing to look for is the squeak. This was caused by severe damage to the U-joint attached to the drive shaft. In addition to noise, you should also look for rust on the bearing cap seals. In extreme cases, your car can even shudder when accelerating.
Vibration while driving can be an early warning sign of a driveshaft failure. Vibration can be due to worn bushings, stuck sliding yokes, or even springs or bent yokes. Excessive torque can be caused by a worn center bearing or a damaged U-joint. The vehicle may make unusual noises in the chassis system.
If you notice these signs, it’s time to take your car to a mechanic. You should check regularly, especially heavy vehicles. If you’re not sure what’s causing the noise, check your car’s transmission, engine, and rear differential. If you suspect that a driveshaft needs to be replaced, a certified mechanic can replace the driveshaft in your car.

Drive shaft type

Driveshafts are used in many different types of vehicles. These include four-wheel drive, front-engine rear-wheel drive, motorcycles and boats. Each type of drive shaft has its own purpose. Below is an overview of the 3 most common types of drive shafts:
The driveshaft is a circular, elongated shaft that transmits torque from the engine to the wheels. Drive shafts often contain many joints to compensate for changes in length or angle. Some drive shafts also include connecting shafts and internal constant velocity joints. Some also include torsional dampers, spline joints, and even prismatic joints. The most important thing about the driveshaft is that it plays a vital role in transmitting torque from the engine to the wheels.
The drive shaft needs to be both light and strong to move torque. While steel is the most commonly used material for automotive driveshafts, other materials such as aluminum, composites, and carbon fiber are also commonly used. It all depends on the purpose and size of the vehicle. Precision Manufacturing is a good source for OEM products and OEM driveshafts. So when you’re looking for a new driveshaft, keep these factors in mind when buying.
Cardan joints are another common drive shaft. A universal joint, also known as a U-joint, is a flexible coupling that allows 1 shaft to drive the other at an angle. This type of drive shaft allows power to be transmitted while the angle of the other shaft is constantly changing. While a gimbal is a good option, it’s not a perfect solution for all applications.
CZPT, Inc. has state-of-the-art machinery to service all types of drive shafts, from small cars to race cars. They serve a variety of needs, including racing, industry and agriculture. Whether you need a new drive shaft or a simple adjustment, the staff at CZPT can meet all your needs. You’ll be back on the road soon!

U-joint

If your car yoke or u-joint shows signs of wear, it’s time to replace them. The easiest way to replace them is to follow the steps below. Use a large flathead screwdriver to test. If you feel any movement, the U-joint is faulty. Also, inspect the bearing caps for damage or rust. If you can’t find the u-joint wrench, try checking with a flashlight.
When inspecting U-joints, make sure they are properly lubricated and lubricated. If the joint is dry or poorly lubricated, it can quickly fail and cause your car to squeak while driving. Another sign that a joint is about to fail is a sudden, excessive whine. Check your u-joints every year or so to make sure they are in proper working order.
Whether your u-joint is sealed or lubricated will depend on the make and model of your vehicle. When your vehicle is off-road, you need to install lubricable U-joints for durability and longevity. A new driveshaft or derailleur will cost more than a U-joint. Also, if you don’t have a good understanding of how to replace them, you may need to do some transmission work on your vehicle.
When replacing the U-joint on the drive shaft, be sure to choose an OEM replacement whenever possible. While you can easily repair or replace the original head, if the u-joint is not lubricated, you may need to replace it. A damaged gimbal joint can cause problems with your car’s transmission or other critical components. Replacing your car’s U-joint early can ensure its long-term performance.
Another option is to use 2 CV joints on the drive shaft. Using multiple CV joints on the drive shaft helps you in situations where alignment is difficult or operating angles do not match. This type of driveshaft joint is more expensive and complex than a U-joint. The disadvantages of using multiple CV joints are additional length, weight, and reduced operating angle. There are many reasons to use a U-joint on a drive shaft.

maintenance interval

Checking U-joints and slip joints is a critical part of routine maintenance. Most vehicles are equipped with lube fittings on the driveshaft slip joint, which should be checked and lubricated at every oil change. CZPT technicians are well-versed in axles and can easily identify a bad U-joint based on the sound of acceleration or shifting. If not repaired properly, the drive shaft can fall off, requiring expensive repairs.
Oil filters and oil changes are other parts of a vehicle’s mechanical system. To prevent rust, the oil in these parts must be replaced. The same goes for transmission. Your vehicle’s driveshaft should be inspected at least every 60,000 miles. The vehicle’s transmission and clutch should also be checked for wear. Other components that should be checked include PCV valves, oil lines and connections, spark plugs, tire bearings, steering gearboxes and brakes.
If your vehicle has a manual transmission, it is best to have it serviced by CZPT’s East Lexington experts. These services should be performed every 2 to 4 years or every 24,000 miles. For best results, refer to the owner’s manual for recommended maintenance intervals. CZPT technicians are experienced in axles and differentials. Regular maintenance of your drivetrain will keep it in good working order.